Great post, Perhaps I missed it, but Gross Weight is a variable. What was yours?
Thanks
Tom
Search found 8 matches
- Fri Aug 23, 2024 7:59 pm
- Forum: Lancair Safety
- Topic: IV-P Best Glide Speed Testing
- Replies: 7
- Views: 1480
- Wed Apr 10, 2024 3:16 pm
- Forum: IV/IV-P/IV-PT
- Topic: Precise Flight Speedbrakes Fail to Retract While in the Air
- Replies: 4
- Views: 2095
Re: Precise Flight Speedbrakes Fail to Retract While in the Air
Ryan, IIt’s definitely both Speedbrakes. I will do more ground testing to see if I can hear a motor running, or something… I removed the panel at the root of the wing — where the fuel probe enters the wing. I didn’t see anything except wire bundles so I suspect that I have the latter version of the ...
- Mon Apr 08, 2024 5:50 pm
- Forum: IV/IV-P/IV-PT
- Topic: Precise Flight Speedbrakes Fail to Retract While in the Air
- Replies: 4
- Views: 2095
Precise Flight Speedbrakes Fail to Retract While in the Air
Flew a number of flights last week in Wickenburg/Buckeye AZ. Most flights at 5,000 ft but one up to 17,000 ft. Speed brakes used a number of times without issue. However, on last flight at 5,000 ft the speed brakes would not retract — tried switch on yoke and also switch on panel. Pulled breaker and...
- Fri Nov 17, 2023 1:07 am
- Forum: IV/IV-P/IV-PT
- Topic: Door Seal Inflation Pump Assembly
- Replies: 17
- Views: 8807
Re: Door Seal Inflation Pump Assembly
George,
Designation and source for valve? What do you use for pinhole sealant? There was a reference to Proseal in another thread but the particular compound no longer seems to be available. Thanks
Best,
Tom
Designation and source for valve? What do you use for pinhole sealant? There was a reference to Proseal in another thread but the particular compound no longer seems to be available. Thanks
Best,
Tom
- Sun Nov 05, 2023 3:17 pm
- Forum: IV/IV-P/IV-PT
- Topic: Door Seal Inflation Pump Assembly
- Replies: 17
- Views: 8807
Re: Door Seal Inflation Pump Assembly
Ryan, Another request would be to up the attachment/picture size limit. Maybe match the “other” board? Storage is cheap these days… Am currently away from my computer setup and find that I can’t reduce picture size directly on an iPad. Have to resort to tedious workarounds. Thanks for your considera...
- Sat Nov 04, 2023 3:34 pm
- Forum: IV/IV-P/IV-PT
- Topic: Door Seal Inflation Pump Assembly
- Replies: 17
- Views: 8807
Re: Door Seal Inflation Pump Assembly
Thanks George for your suggestion. I did spray with soapy water with door closed and found no bubbles. But a better test would be to jumper the door contacts and spray when door open, assuming 20 psi will not blow the seal. I suspect the check valve. A kind soul on the other list posted a schematic ...
- Sat Nov 04, 2023 2:17 am
- Forum: IV/IV-P/IV-PT
- Topic: Door Seal Inflation Pump Assembly
- Replies: 17
- Views: 8807
Door Seal Inflation Pump Assembly
Any insight appreciated… In my IV-P, the door seal inflation pump assembly is entirely located within the door. (This may be a quick build door.) On the ground at 2,380 ft. MSL, it takes 9 to 10 seconds for the door seal to fully inflate. And then every 30 to 45 seconds the pump chirps less than a s...
- Wed Oct 11, 2023 12:52 am
- Forum: Lancair Safety
- Topic: LOBO Training & Fatalities
- Replies: 6
- Views: 4831
LOBO Training & Fatalities
I think that I heard at the recent LOBO conference a statement that there has never been a LOBO-trained pilot fatality? Well, a friend has called BS on this... e says there are easily a handful with Neal Longwill being the latest? Perhaps it depends on the definition of a LOBO trained pilot? What wo...